Free tool
OBD2 code lookup for check engine light codes
An OBD2 trouble code has five characters: a letter for the system (P powertrain, C chassis, B body, U network), then a digit that shows whether the code is generic or set by the maker, then the subsystem and the specific fault. Enter a code to decode it, and browse the plain meaning of 158 common generic P0 codes.
Five characters: a letter (P, C, B or U) and four characters, such as P0301 or P042A. Any OBD2 scan tool reads the code.
Check engine light flashing?
A flashing check engine light means a severe misfire. Wisconsin's emissions program advises reducing speed and getting service as soon as possible, and Connecticut's says to stop driving and have the vehicle checked, because the misfire can overheat the catalytic converter.
What the code means
P0420
Catalytic converter not cleaning the exhaust as well as required, bank 1
- First character (P): system
- Powertrain (engine, transmission and emissions)
- Second character (0): code type
- SAE generic: makers agreed to use the standard meaning, though a few vary
- Third character (4): subsystem
- Auxiliary emission controls
- Last two characters (20): specific fault
- They identify the exact fault within the system. They can include letters, as in P042A.
A code tells you which system or circuit the computer flagged, not which part failed. A mechanic should test and confirm the cause before parts are replaced.
Heavy trucks: engines on the SAE J1939 network report faults as an SPN (what failed) and an FMI (how it failed) rather than a P code, and some report both. High Point GPS tracking devices read engine fault codes from light vehicles and heavy trucks and show them in MyGeotab.
158 common generic codes
| Code | Meaning |
|---|---|
| Mass air flow (MAF) sensor: circuit fault | |
| Mass air flow (MAF) sensor: reading outside the expected range | |
| Mass air flow (MAF) sensor: signal too low | |
| Mass air flow (MAF) sensor: signal too high | |
| Mass air flow (MAF) sensor: signal comes and goes | |
| Manifold absolute pressure (MAP) or barometric pressure sensor: circuit fault | |
| Manifold absolute pressure (MAP) or barometric pressure sensor: reading outside the expected range | |
| Manifold absolute pressure (MAP) or barometric pressure sensor: signal too low | |
| Manifold absolute pressure (MAP) or barometric pressure sensor: signal too high | |
| Intake air temperature sensor: reading outside the expected range | |
| Intake air temperature sensor: signal too low | |
| Intake air temperature sensor: signal too high | |
| Engine coolant temperature sensor: circuit fault | |
| Engine coolant temperature sensor: reading outside the expected range | |
| Engine coolant temperature sensor: signal too low | |
| Engine coolant temperature sensor: signal too high | |
| Throttle or pedal position sensor A: circuit fault | |
| Throttle or pedal position sensor A: reading outside the expected range | |
| Throttle or pedal position sensor A: signal too low | |
| Throttle or pedal position sensor A: signal too high | |
| The engine takes too long to warm up enough for the computer to control the fuel mixture from the oxygen sensors | |
| Oxygen sensor, bank 1 sensor 1: circuit fault | |
| Oxygen sensor, bank 1 sensor 1: voltage too low | |
| Oxygen sensor, bank 1 sensor 1: voltage too high | |
| Oxygen sensor, bank 1 sensor 1: slow response | |
| Oxygen sensor, bank 1 sensor 1: no activity detected | |
| Oxygen sensor, bank 1 sensor 1: heater circuit fault | |
| Oxygen sensor, bank 1 sensor 2: circuit fault | |
| Oxygen sensor, bank 1 sensor 2: voltage too low | |
| Oxygen sensor, bank 1 sensor 2: voltage too high | |
| Oxygen sensor, bank 1 sensor 2: slow response | |
| Oxygen sensor, bank 1 sensor 2: no activity detected | |
| Oxygen sensor, bank 1 sensor 2: heater circuit fault | |
| Oxygen sensor, bank 2 sensor 1: circuit fault | |
| Oxygen sensor, bank 2 sensor 1: voltage too low | |
| Oxygen sensor, bank 2 sensor 1: voltage too high | |
| Oxygen sensor, bank 2 sensor 1: slow response | |
| Oxygen sensor, bank 2 sensor 1: no activity detected | |
| Oxygen sensor, bank 2 sensor 1: heater circuit fault | |
| Oxygen sensor, bank 2 sensor 2: circuit fault | |
| Oxygen sensor, bank 2 sensor 2: voltage too low | |
| Oxygen sensor, bank 2 sensor 2: voltage too high | |
| Oxygen sensor, bank 2 sensor 2: slow response | |
| Oxygen sensor, bank 2 sensor 2: no activity detected | |
| Oxygen sensor, bank 2 sensor 2: heater circuit fault | |
| Fuel trim fault, bank 1: the computer can no longer correct the fuel mixture | |
| Mixture too lean, bank 1: too much air or too little fuel | |
| Mixture too rich, bank 1: too much fuel or too little air | |
| Fuel trim fault, bank 2: the computer can no longer correct the fuel mixture | |
| Mixture too lean, bank 2: too much air or too little fuel | |
| Mixture too rich, bank 2: too much fuel or too little air | |
| Fuel rail pressure sensor: circuit fault | |
| Fuel rail pressure sensor: reading outside the expected range | |
| Fuel rail pressure sensor: signal too low | |
| Fuel rail pressure sensor: signal too high | |
| Fuel injector circuit fault | |
| Fuel injector circuit fault, cylinder 1 | |
| Fuel injector circuit fault, cylinder 2 | |
| Fuel injector circuit fault, cylinder 3 | |
| Fuel injector circuit fault, cylinder 4 | |
| Fuel injector circuit fault, cylinder 5 | |
| Fuel injector circuit fault, cylinder 6 | |
| Fuel injector circuit fault, cylinder 7 | |
| Fuel injector circuit fault, cylinder 8 | |
| Engine overheating detected | |
| Engine speed went above the allowed limit (overspeed) | |
| Fuel pump primary circuit fault | |
| Turbocharger or supercharger boost higher than allowed (overboost) | |
| Misfires detected in several cylinders or at random | |
| Misfire detected in cylinder 1 | |
| Misfire detected in cylinder 2 | |
| Misfire detected in cylinder 3 | |
| Misfire detected in cylinder 4 | |
| Misfire detected in cylinder 5 | |
| Misfire detected in cylinder 6 | |
| Misfire detected in cylinder 7 | |
| Misfire detected in cylinder 8 | |
| Knock sensor 1 circuit fault (bank 1 or single sensor) | |
| Knock sensor 1: signal too low (bank 1 or single sensor) | |
| Knock sensor 1: signal too high (bank 1 or single sensor) | |
| Knock sensor 2 circuit fault (bank 2) | |
| Crankshaft position sensor A circuit fault | |
| Crankshaft position sensor A: reading outside the expected range | |
| Camshaft position sensor circuit fault | |
| Camshaft position sensor: reading outside the expected range | |
| Ignition coil primary or secondary circuit fault | |
| Ignition coil A: primary or secondary circuit fault | |
| Ignition coil B: primary or secondary circuit fault | |
| Ignition coil C: primary or secondary circuit fault | |
| Ignition coil D: primary or secondary circuit fault | |
| Glow plug or heater circuit A fault (diesel) | |
| Exhaust gas recirculation (EGR) flow fault | |
| Exhaust gas recirculation (EGR) flow too low | |
| Exhaust gas recirculation (EGR) flow too high | |
| Exhaust gas recirculation (EGR) circuit fault | |
| Exhaust gas recirculation (EGR) circuit: reading outside the expected range | |
| Exhaust gas recirculation (EGR) sensor A: signal too low | |
| Exhaust gas recirculation (EGR) sensor A: signal too high | |
| Secondary air injection system fault | |
| Secondary air injection: wrong air flow detected | |
| Catalytic converter not cleaning the exhaust as well as required, bank 1 | |
| Warm-up catalytic converter efficiency below the required level, bank 1 | |
| Catalytic converter not cleaning the exhaust as well as required, bank 2 | |
| Warm-up catalytic converter efficiency below the required level, bank 2 | |
| Fuel vapour (EVAP) system fault | |
| Fuel vapour (EVAP) system: wrong purge flow | |
| Fuel vapour (EVAP) system: small leak detected | |
| Fuel vapour (EVAP) purge control valve circuit fault | |
| Fuel vapour (EVAP) purge control valve circuit shorted | |
| Fuel vapour (EVAP) vent control circuit fault | |
| Fuel vapour (EVAP) vent valve or solenoid circuit fault | |
| Fuel vapour (EVAP) pressure sensor fault | |
| Fuel vapour (EVAP) pressure sensor: reading outside the expected range | |
| Fuel vapour (EVAP) pressure sensor: signal too low | |
| Fuel vapour (EVAP) pressure sensor: signal too high | |
| Fuel vapour (EVAP) system: large leak detected | |
| Fuel level sensor: circuit fault | |
| Fuel level sensor: reading outside the expected range | |
| Fuel level sensor: signal too low | |
| Fuel level sensor: signal too high | |
| Cooling fan 1 control circuit fault | |
| Cooling fan 2 control circuit fault | |
| Vehicle speed sensor fault | |
| Vehicle speed sensor: reading outside the expected range | |
| Vehicle speed sensor: signal too low | |
| Idle control system fault | |
| Idle speed lower than expected | |
| Idle speed higher than expected | |
| Engine oil pressure sensor or switch circuit fault | |
| Engine oil pressure sensor or switch: reading outside the expected range | |
| Engine oil pressure sensor or switch: voltage too low | |
| Engine oil pressure sensor or switch: voltage too high | |
| System voltage fault | |
| System voltage too low | |
| System voltage too high | |
| Communication link fault between control modules | |
| Control module memory checksum error | |
| Control module programming error | |
| Control module keep-alive memory (KAM) error | |
| Control module random access memory (RAM) error | |
| Control module read-only memory (ROM) error | |
| Engine computer (PCM) processor fault | |
| Alternator (generator) control circuit fault | |
| Check engine light (MIL) control circuit fault | |
| The transmission computer has stored its own trouble code: read the transmission codes | |
| Transmission range sensor circuit fault (gear selector position) | |
| Transmission fluid temperature sensor circuit fault | |
| Transmission input or turbine speed sensor circuit fault | |
| Transmission output speed sensor circuit fault | |
| Incorrect gear ratio | |
| Gear 1: incorrect ratio | |
| Gear 2: incorrect ratio | |
| Gear 3: incorrect ratio | |
| Gear 4: incorrect ratio | |
| Torque converter clutch circuit fault | |
| Torque converter clutch: poor performance or stuck off | |
| Shift solenoid A fault | |
| Shift solenoid B fault |
Sources, checked November 5, 2026: SAE J2012, Diagnostic Trouble Code Definitions (the standard); Maryland Department of the Environment, Decoding DTCs; Delaware DMV, On-Board Diagnostic Trouble Codes; US EPA, OBD frequently asked questions; Wisconsin and Connecticut emissions programs (flashing light); SAE J1939-73 (heavy-duty diagnostics). Meanings are in our own plain words; the maker's service information takes precedence.
Why read the code before the repair
Since the 1996 model year, light-duty cars and trucks have an on-board diagnostic system that turns on the check engine light and stores a code when it finds a fault. The code tells the mechanic where to start looking. Reading it yourself helps you judge how urgent the problem is, describe it to the shop, and see whether the same fault keeps coming back.
Fault codes without plugging in a scanner
High Point GPS tracking devices read engine fault codes from each vehicle along with engine hours, fuel use and idle time, so the fleet manager sees a new code without waiting for the driver to report the light. Maintenance reminders by distance or engine hours, and FleetZap work orders, turn the code into a scheduled repair.
Get a quoteTips when the check engine light comes on
Write down every code before anyone clears it, so the mechanic sees what the computer found.
If the light comes on after refuelling, check that the fuel cap is tight: a loose cap can set an EVAP leak code, and the light can go out by itself once it is tightened.
A code that comes back after a repair means the cause was not fixed: give the shop the history of each code.
On heavy trucks, read faults with a tool that supports J1939, since many trucks report SPN and FMI codes rather than P codes.
OBD2 code questions
- What does the check engine light mean?
- It means the on-board diagnostic system found a problem with the engine, transmission or emission controls and stored a trouble code. A steady light means the vehicle should be serviced soon. A flashing light means a severe misfire that can damage the catalytic converter, so slow down and get the vehicle checked as soon as possible.
- What does P0420 mean?
- P0420 means the computer found that the catalytic converter on bank 1 is not cleaning the exhaust as well as required; the standard description is catalyst system efficiency below threshold. P0430 is the same fault on bank 2. The code points to the converter system, so a mechanic should confirm the cause before the converter is replaced.
- What is the difference between generic and manufacturer codes?
- Generic codes have a meaning set by the SAE J2012 standard that carmakers agreed to use, so P0300 is a misfire on any make. Manufacturer codes, with a 1 as the second character such as P1xxx, mean whatever the maker defines. P3 codes are split: P3000 to P3399 are manufacturer codes and P3400 to P3499 are generic.
- Why does my truck show SPN and FMI codes instead of P codes?
- Most heavy trucks use the SAE J1939 network, which reports a fault as a suspect parameter number (SPN) that says what failed and a failure mode identifier (FMI) that says how it failed. Some heavy engines report P codes as well. A scan tool that supports J1939, or a telematics device, reads these codes.
- Will clearing the code fix the problem?
- No. Clearing a code turns the light off but repairs nothing, and the light comes back when the system finds the fault again. The system can also turn the light off by itself once the problem is gone, as with a fuel cap that was not tight. Write the code down before clearing it so the mechanic knows what was found.