Free tool
Trailer and box truck dimensions: how many pallets fit
The number of pallets that fit depends on the inside length and width of the trailer or box, which each manufacturer sets. Enter your trailer's interior size and a pallet size, and the tool counts pallets loaded straight, turned and in the best mix, single or double stacked.
The 630 × 100 in floor shown is an example, not a standard. Measure your own trailer or box.
Pallets that fit
- Best layout
- 30 pallets
- All straight
- 26
- All turned
- 30
- Floor covered (best layout)
- 91 %
Floor count only: it does not check height, weight, load securement or axle limits. To work out volume, use the cubic feet calculator.
US federal size rules on the National Network: States may not limit a semitrailer in a tractor-semitrailer combination to less than 48 ft (23 CFR 658.13), and must allow a width of 102 in (23 CFR 658.15). Checked November 5, 2026.
Sources: 23 CFR 658.13 and 658.15 (ecfr.gov); pallet sizes from GS1's code list T2244, Platform type code (gs1.se/en/guides/documentation/code-lists/t2244-platform-type-code).
Why count pallets before you load
Pallet count decides how many trucks a shipment needs and whether a load fits at all. Turning pallets sideways often fits more on the floor, and the right pattern can save a trip. Interior sizes vary between trailer and box truck models, and between new and older equipment, so counting from your own measurements is safer than relying on a figure for a typical trailer.
Plan the trip once the load fits
High Point GPS fleet tracking records every trip, the distance run, idle time and fuel use from engine data for each truck. Geofences around docks and customer sites show when a trailer arrives and leaves, so you can see how long loading takes and which stops hold trucks up.
Get a quoteTips for an accurate pallet count
Measure the inside of the trailer at the narrowest point, such as between the wheel wells or the door frame, not the outside size.
Leave room for overhang: a load that sticks out past the pallet edge takes the floor space of its widest point.
Double stacking needs both the height and the weight to allow it. Check the interior height, the pallet load rating and the truck's weight limits.
For cubic space instead of floor space, work out the volume of the load with a cubic feet calculator.
Trailer and pallet questions
- How many pallets fit in a 53 foot trailer?
- It depends on the inside length and width of the trailer and the pallet size. With 48 × 40 inch pallets, loading them turned so the 40 inch side runs along the trailer usually fits more than loading them straight. Enter your trailer's interior measurements in the calculator to get the count for your equipment, single or double stacked.
- What are the dimensions of a 53 ft trailer?
- The 53 feet is the trailer's outside length. Its inside length, width and height are set by the manufacturer and change with the model, wall type and refrigeration unit, so check the specification sheet or measure. US federal rules require States to allow semitrailers of at least 48 feet and a width of 102 inches on the National Network.
- What are box truck dimensions?
- Box truck sizes are set by the body manufacturer, so the inside length, width and height differ between models even when the box is sold as the same nominal length. Look at the body's specification plate or sales sheet, or measure the inside of the box, then enter the length and width here to see how many pallets fit on the floor.
- What size is a standard pallet?
- In North America, the common pallet is 48 × 40 inches (1,219 × 1,016 mm). In Europe, the ISO 6780 sizes 1,200 × 800 mm (the EUR pallet) and 1,200 × 1,000 mm are common. GS1's platform code list names all three. The calculator also takes a custom size if you ship on other pallets or skids.
- What does straight or turned loading mean?
- Straight loading puts the pallet's long side along the length of the trailer. Turned loading rotates every pallet so the short side runs along the trailer. The best mix combines straight and turned rows to fill the floor, and the calculator tries every combination and shows the highest count it finds for one layer.